This Mod Podge DIY recipe holder makes the perfect gift! It’s a great idea for the cook in your life, and so easy to make (and personalize).
Man Podger David returns this week with a great gift idea for the person in your life who loves cooking – a DIY recipe holder. That would not be me. Ha!
I’m not a baker or a chef, but you know what – I want to be one day. I do love traditional recipes though.
My mom makes Swedish pancakes from my great-grandfather’s recipe, and I hope one day she shows me how to make them. When she does, I’ll use this recipe holder. Here’s how to do it, from David.
DIY Recipe Stand
I have a sweet tooth.
Well, to be honest, I only eat dinner to justify having dessert.
My mom is an excellent baker. She even makes donuts. SHE. MAKES. DONUTS. PEOPLE!!!!! Seriously, you have no idea how good they are.
Mom has given me some favorite recipes carefully written out on index cards and, being me, I tend to send those flying into the sink or onto the floor whenever I use them.
So I came up with this little project to both honor my mom and to keep the cards safe and where I can find them in the kitchen.
I realize not everyone will want to use their mom’s recipes for the design, but this is a great project for using up any scraps of paper that appeal to you.
You will need:
- Wooden plaque base
- Clothespin – whatever size appeals
- Scrap piece of wood for the stem, preferably the same width as your clothespin
- Saw
- Paper
- Mod Podge
- Foam Brush
- Rubber band
- Glue (I used Gorilla Glue but any strong glue will do)
- Drill
- Screws – 2
- Paint
- Scissors
- Sandpaper
(If you’re curious about my paper – I just scanned a couple of my mom’s recipes, resized them alittle,printed them out, cut them up to make a “collage” and then re-scanned the whole thing and printed itout).
Step 1: Cut the Stem
Mark and cut a 35 degree angle into your scrap piece of wood.
Then cut the piece so it measures 3 ¾” high.
Step 2: Sand and Paint
Lightly sand and then paint your base (I remembered this time!), stem, and clothespin.
You will need to take the clothespin apart to do this. Be sure to put the stupid little springy thing that holds the pin together somewhere that you’ll remember.
If you do this you will save time and be able to skip Step 8a:Where The Heck Did I Put That Stupid Little Springy Thing That Holds It Together.
I did not skip Step 8a.
Step 3: Mod Podge
Using Mod Podge, attach your paper to the base and the top of the clothespin – use dampened fingers to smooth out any bubbles. After they have dried, I like to add a finishing coat of Mod Podge.
Step 4: Drill Pilot Holes
After your sealer coat has thoroughly dried center your stem on the base and, using a pencil, outline where it will go.
Step 5: Attach the Screws
Next drill two pilot holes by drilling down through your base.
Drill the screws up and through the base – making sure that they are at approximately equal heights.
Step 6: Mark the Stem
Gently press the bottom of the stem into the screws to mark where the screws will go and then drill shallow pilot holes there.
You’re doing this because you’re drilling into the end of the wood, and this will prevent the wood from splitting when you screw into it.
Step 7: Attach the Base to the Stem
Screw the base to the stem, making sure that the heads of your screws are flush with the bottom of the base (so it can sit flat).
Step 8a, also known as Where the Heck Did I Put That Stupid Little Springy Thing
Reassemble the clothespin.
Step 8: Attach the Clothespin
Glue the clothespin to the stem and then use the rubber band to hold it in place to dry.
That’s all to making your DIY recipe holder, besides letting it dry.
This DIY recipe holder is a versatile project. You can make it bigger or smaller depending on your need. Other thoughts.
- You could Mod Podge paper onto the stem, or leave it unpainted for a more natural look.
- If you don’t like using drills and such you can achieve the whole thing using just strong glue and a little patience while you hold it in place to dry.
Yield: 1 holder
Recipe Holder
Learn how to make a DIY recipe holder using wood parts and a clothespin! Decorate it for a gift or home decor.
Prep Time30 minutes
Active Time1 hour 30 minutes
Total Time2 hours
DifficultyEasy
Estimated Cost$3
Materials
- Wooden base - square plaque
- Clothespin
- Scrap piece of wood for the stem
- Paper
- Mod Podge
- Rubber band
- Gorilla Glue
- Screws - 2
- Paint
- Sandpaper
Tools
- Saw
- Paintbrush
- Drill
- Scissors
Instructions
- Mark and cut a 35 degree angle into the scrap piece of wood using the saw. Cut the piece so it measures 3 ¾” high.
- Lightly sand and then paint the base, stem, and clothespin (take the clothespin apart).
- Trim the paper to fit the base and top of the clothespin. Use Mod Podge to attach the paper to both. Smooth and let dry.
- Center your stem on the base and, using a pencil, outline where it will go.
- Drill two pilot holes by drilling down through the base. Drill the screws up through the bottom to equal heights.
- Press the bottom of the stem into the screws to mark position and drill pilot holes into the stem.
- Screw the base to the stem, making sure that the heads of your screws are flush with the bottom of the base.
- Glue the clothespin to the stem and then use the rubber band to hold it in place to dry.
I hope you enjoyed this wood craft and, as always, I will monitor the comments and if you have any questions or need any clarifications please don’t hesitate to ask. I’d also love for you to visit some of my other favorite projects:
- Easy DIY Photo Display for Beginners
- DIY Magnetic Board for a Message Center
- DIY Plate Display Using Vintage Photos
- Make Industrial Picture Frames Using Pipe
- Clothespin Wreath Made the Easy Way
Thanks David – love this project, even if I don’t cook (yet).To all of you, don’t forget to visit David’s Etsy shop here!